Advantages

• Corrosion Resistant All Plastic Construction.
• Self-Priming.
• Repeat Accuracy - 0.5 percent.
• Long Cycle Life.
• Patented Fail-Dry Vented Safety Design.
• Standard Limit Stop allows virtually unlimited pumping volume adjustment.
• Optional proximity switches provide remote sensing & position verification.

Design

Series VPA metering pumps are air-operated, self-priming, positive displacement type pumps designed to meter precise quantities of liquids. The accuracy of the discharge repeatability is approximately 1/2 of 1%. The four sizes of pumps available have a single stroke maximum delivery capacity of 7, 10, 32 or 128 liquid ounces. Using the standard limit stop, the pump can be adjusted to deliver smaller portions of its stated capacity.

Materials of Construction

Pump bodies, shaft and piston assemblies, and cylinder walls are constructed of Geon ® brand TYPE 1, GRADE 1 PVC (Polyvinyl Chloride). Polypropylene, Kynar ® PVDF and PTFE also available on request. Optional stainless steel cylinder walls are available when chemicals are compatible with 304 stainless steel.

A choice of two standard elastomer seals is offered: Buna-N (nitrile rubber) and FKM (fluorocarbon rubber). Optional PTFE cap seals are offered for applications where severe seal rubbing occurs.

Pump tie rods and their fasteners, adjusting bolts, locking nuts, as well as inlet and outlet check fasteners, are 303 stainless steel. Mounting brackets are zinc plated steel.

Cycle Life

Tests conducted in our laboratory, pumping tap water, indicate the life expectancy of pumps with PVC cylinder walls to be between 100,000 and 300,000 cycles. Over 1,000,000 cycles is achieved in testing with the optional stainless steel cylinder walls.

To ensure the best cycle figures pumps must always be mounted vertically. When gritty liquids are being pumped it is recommended that the pumps be mounted with the liquid side down to allow sediment to settle without scoring the cylinder walls. The optional PTFE cap seals do not increase cycle life with PVC cylinders unless there is an unusual rubbing problem with the O-rings. There is a cycle life improvement with the PTFE cap seals in stainless cylinders.

Capacity & Accuracy

Plast-O-Matic Series VPA chemical metering pumps are available with maximum per cycle capacities of 7 ounces, 10 ounces, 32 ounces and 128 ounces. A cycle is one up and down stroke of the piston assembly. They can be cycled up to 10 times per minute when pumping water or liquids of similar specific gravities and viscosities. The per cycle discharge capacity can be adjusted from its maximum to 20% of its maximum. For example: the 128 ounce pump can be adjusted to discharge anywhere between 25 and 128 ounces per stroke. While the pump discharge adjustment is simple, it is recommended that the discharge amount be physically measured. Once the measured amount is set and checked the accuracy of the discharge repeatability is approximately 1/2 of 1%.

Viscosity

The maximqm liquid viscosity recommended (at 0.9 specific gravity @ 65° F) is 85,000 SSU, which is equivalent to 17,000 centipoise or 19,000 centistokes. At these viscosity values the pumping time required to complete a cycle is as follows: 1 cycle/ minute with 25 psi air supply, 3.4 cycles/minute with 75 psi air, and 4.3 cycles/minute with 100 psi air. (Test media: honey, which is 17,000 centipoise at room temperature.)

Fail-Dry Vent

PLAST-O-MATIC chemical metering pumps feature the patented FAIL-DRY* design concept of having a vented chamber separating two sealed sections of a valve or, as in this case, a pump. In the event of a liquid piston seal failure, the vented chamber and u-cup seals will cause the by-passing liquid to exit at the vent port. With the vent piped to a remote location, the pump will remain functioning even after a primary seal failure, thereby keeping the process or system operating until a maintenance can be scheduled avoiding costly emergency shutdown.

Operation

Plast-O-Matic chemical metering pumps are designed with 4 chambers, a liquid chamber, a vented chamber, and two air operating chambers. Movement within the chambers is controlled by the reciprocating action of a pump's shaft and piston assembly. The assembly is operated and controlled by a 4-way air valve (an accessory item) which alternately introduces and exhausts air pressure on both sides of the air piston. The 4-way valve would receive its on-off electrical signal from an independent electrical timer or similar device, not supplied with the pump. This action also causes the liquid piston to reciprocate.

On the down stroke of the liquid piston a vacuum is created in the liquid chamber which opens the inlet check valve diaphragm and holds the outlet check diaphragm closed. This operation permits the liquid chamber to fill itself (self priming).

On the up stroke the liquid in the chamber is pressurized by the piston movement. This opens the outlet check valve diaphragm and holds the inlet check valve diaphragm closed. This action discharges the liquid out of the pump into a system.

Limit Stop (Capacity Adjustment)

All Plast-O-Matic True Blue chemical metering pumps are positive displacement pumps thus any re-adjustments to the adjusting bolt will result in a change in discharge quantity. By turning the bolt further into the lower air chamber the travel of the shaft and piston assembly is restricted creating a shorter discharge stroke and reduced discharge quantity.

Optional Switches

Proximity sensors are available to verify position on all metering pump sizes. These can be used to power a relay, or signal a computer or other process control. Switches are ideal to verify that the pump has discharged or retracted, or both. 5-240 VAC or DC Switches feature Indicator Lights, NEMA 6 washdown compatible, thermoplastic (Ultem) housing, PVC wire and stainless steel fasteners. Universal clamp attaches to tie rods on pump cylinders.

Dimensions of 32 & 128 ounce models::