plastomatic Series ARV Thermoplastic Air Release Valves, ARV050EPT-PV, ARV075EPT-PV, ARV100EPT-PV

Untitled Document

	Air Release/Degassing Valves
		Series ARV Air Release Valves

		Series DGV Degassing Valves

Series ARV Air Release Valves

Series ARV

Series ARV Thermoplastic Air Release Valves

Self-Guided Poppet Assures Dependable, Repetitive Operation

Features/Benefits:

Safety: Allows safe expulsion of unwanted air in piping systems.
Dependability: Unique self-guided poppet assures minimal emission of system liquid prior to sealing.
Convenience: True-union simplifies valve inspection/removal with minimum piping breakdown.
Minimal Closing Pressure: Closes at 0 PSI, as long as liquid is present. Valve closes as liquid rises, after virtually all unwanted air is forced out. Seals bubble tight at system pressures as low as 10 psi (EPDM seals).
Cost Efficient: Designed to improve system performance and competitively priced.
Superior Design: Poppet seals more reliably than ball designs; does not deform under pressure like a hollow ball.
Corrosion Resistant: Top quality thermoplastics and elastomers resist chemical attack and protect system purity. No metal components in Series ARV.

How it Works:

Series ARV is a normally-open valve. Until your system is pressurized, the valve is simply open, and air is present. As pressure builds within the system, unwanted air is forced to the highest point in the system, i.e., the normally-open Air Release Valve. When pressure within the system exceeds atmospheric pressure, air is expelled. As liquid rises, the poppet becomes buoyant and eventually closes. (Note minimum specific gravity of liquid must be .9 or higher). It is possible that trace amounts of air will remain in the system, depending on the rapidity with which the valve closes. It is also likely that some trace amounts of process liquid will be emitted. At system pressure of 10 psi (with EPDM elastomer), the poppet will seal bubble tight against the orifice. When pressure and liquid level drop, the valve will automatically re-open. 1

The poppet is guided by a series of thermoplastic ribs within the valve. The poppet is a unique design by Plast-O-Matic Valves, Inc. that is engineered to provide a balance of buoyancy and sealability. This balanced poppet is the key to the superior performance of this valve: It is dense enough to permit maximum emission of unwanted system air, yet buoyant enough to affect a quick seal and minimize emission of the process liquid. Historically, competitive air release valves have used ball-type sealing mechanisms that either seal too rapidly or allow excessive liquid to escape.

1 Note that although Series ARV is a normally open valve, it should not be used in lieu of a vacuum breaker due to safety considerations. Under certain conditions, a normally-open air release valve will not perform properly as a vacuum breaker.

Specifications:

Available in Geon® PVC & Corzan® CPVC
Series ARV Pipe Size (NPT)	A		B		C		Model Number
Series ARV Pipe Size (NPT)	IN.	mm	IN.	mm	IN.	mm	Model Number
1/2"	5.3	130	1.9	48	2.8	72	ARV050EPT-PV
3/4"	5.3	130	1.9	48	2.8	72	ARV075EPT-PV
1"	4.7	120	1.9	48	2.8	72	ARV100EPT-PV
ARV(series) 050(size) EP(seal material) T(threaded) - PV(body material) Part numbers shown are EPDM seals with PVC bodies. Note that all three sizes are based on the 1" valve; the 1/2" and 3/4" sizes use reducing bushings. • For Viton seals, change "EP" to "V" (ARV050VT-PV) • For Corzan CPVC body, change "-PV" to "-CP" (ARV050VT-CP) • Standard connections are threaded. For socket connection, change "T" to "S" after seal material (ARV050EPS-PV) • For spigot or other connection types, consult factory.

Additional Specifications
Pressure required for bubble-tight seal	EPDM Elastomer: 10 PSI	Viton Elastomer: 15 - 20 PSI
Pressure Rating at 70ºF	150 PSI
Maximum Air Flow Rate**	Air Flow Rate: 8 SCFM	Liquid Flow Rate: 60 GPM
**Note that excess of 8 SCFM airflow out of the valve will have sufficient force to lift and close the poppet, even though more air may be in the system. Liquid pumping into the system at flow rate exceeding 60 GPM (225 LPM) will create airflow in excess of 8 SCFM.